Bump Bending Tutorial - Revision history

Fabcam1 at 16:54, 23 July 2013

2013-07-23T16:54:41Z

Fabcam1 at 16:52, 23 July 2013

2013-07-23T16:52:41Z

Fabcam1 at 16:24, 23 July 2013

2013-07-23T16:24:41Z

Fabcam1 at 15:48, 23 July 2013

2013-07-23T15:48:17Z

Fabcam1 at 15:37, 23 July 2013

2013-07-23T15:37:10Z

Fabcam1 at 15:13, 23 July 2013

2013-07-23T15:13:40Z

Fabcam1 at 21:30, 22 July 2013

2013-07-22T21:30:15Z

Fabcam1: Created page with "==Introduction== This tutorial will step through the process of using the bump bending plug-in. The bump bending plug in allows bends of larger radii to b..."

2013-07-22T21:03:41Z

Created page with "==Introduction== This tutorial will step through the process of using the bump bending plug-in. The bump bending plug in allows bends of larger radii to b..."

New page

==Introduction==

This tutorial will step through the process of using the [[Bump Bending|bump bending]] plug-in.

The bump bending plug in allows bends of larger radii to be split into multiple, more manageable bends.

==Tutorial==

==='''Step 1'''===

==='''Step 2'''===

==='''Step 3'''===

@@ Line 107: / Line 107: @@
 ==='''Step 9'''===
-In the die menu, '''select the 100mm die''' (''This die was made in the [[Die Library Tutorial]]. If this die is not shown in the die selection menu, either complete the die library tutorial or just select any other die that is available.''). '''''Note:''''' ''This die will be the die that is initially selected for each of these bends. After the bump bends are added, each can be given a different die if necessary.''
+In the die menu, '''select the 100mm die''' (''This die was made in the [[Die Library Tutorial]]. If this die is not shown in the die selection menu, either complete the die library tutorial or just select any other die that is available.''). This die will be initially selected for each of these bends. After the bump bends are added, each can be given a different die if necessary.
 In the bend menu, '''select bend 1'''.

@@ Line 107: / Line 107: @@
 ==='''Step 9'''===
-In the die menu, '''select the 100mm die''' (''This die was made in the [[Die Library Tutorial]]. If this die is not shown in the die selection menu, either complete the die library tutorial or just select any other die that is available.'').
+In the die menu, '''select the 100mm die''' (''This die was made in the [[Die Library Tutorial]]. If this die is not shown in the die selection menu, either complete the die library tutorial or just select any other die that is available.''). '''''Note:''''' ''This die will be the die that is initially selected for each of these bends. After the bump bends are added, each can be given a different die if necessary.''
 In the bend menu, '''select bend 1'''.

@@ Line 43: / Line 43: @@
 [[File:temptut9.png]]
@@ Line 50: / Line 51: @@
 ==='''Step 4'''===
 Now the large radius part will be designed. The part will have a single 180° bend with two equal sized lengths on either side.
@@ Line 77: / Line 62: @@
-==='''Step 6'''===
+==='''Step 5'''===
 Next, '''a custom CLR will be applied to the bend'''.
@@ Line 89: / Line 74: @@
-==='''Step 7'''===
+==='''Step 6'''===
 Now the '''part design is complete'''.
@@ Line 98: / Line 83: @@
-==='''Step 8'''===
+==='''Step 7'''===
 Now the '''1200 mm radius bend will be broken up into separate smaller bends''' using the bump bending plug-in.
@@ Line 110: / Line 95: @@
-==='''Step 9'''===
+==='''Step 8'''===
 '''This will open a small window''' where the die, bend, and number of bends can be chosen and applied to the bend.
@@ Line 121: / Line 106: @@
-==='''Step 10'''===
+==='''Step 9'''===
 In the die menu, '''select the 100mm die''' (''This die was made in the [[Die Library Tutorial]]. If this die is not shown in the die selection menu, either complete the die library tutorial or just select any other die that is available.'').
@@ Line 138: / Line 123: @@
-==='''Step 11'''===
+==='''Step 10'''===
 The large 180° bend with a 1200 mm radius will now be separated into '''eight different 22.5° bends where each is the same distance apart and bent with the 100mm die'''.
@@ Line 150: / Line 135: @@
-==='''Step 12'''===
+==='''Step 11'''===
 '''The tutorial is complete!'''
 For further information, see the '''[[Bump Bending]]''' plug-in page.

@@ Line 58: / Line 58: @@
 [[File:bbend04.png]]
@@ Line 142: / Line 143: @@
 The '''entry fields and results table''' will be modified to include the bends that have been added to the part.
-[[File:bbend11.png|bbend11.png]]
+[[File:bbend11.png|700px]]

@@ Line 2: / Line 2: @@
 This tutorial will step through the process of using the [[Bump Bending|bump bending]] plug-in.
-The bump bending plug in allows bends of larger radii to be sectioned off into multiple, equal sized bends to simplify the bending process.
+The bump bending plug in allows bends of larger radii to be sectioned off into multiple, equal sized, and equally distanced bends to simplify the bending process.
@@ Line 127: / Line 127: @@
 And in the number of bend field, '''enter 8'''.
-'''Click the green check button''' to apply the bump bends to the bend.
 [[File:bbend10.png]]

@@ Line 21: / Line 21: @@
 ==='''Step 2'''===
-[[File:lin2dtut6.png|right]]Now, '''the die and material need to to be chosen'''. The die and material menus are located in the upper left corner of the designer window.
+This will open a '''new linear 2D part design window'''.
@@ Line 39: / Line 49: @@
-==='''Step 3'''===
+==='''Step 4'''===