Linear Dynamic Designer Quick Start - Revision history

Fabcam1 at 18:40, 1 August 2013

2013-08-01T18:40:50Z

2013-06-19T16:26:36Z

2013-05-29T20:51:34Z

2013-05-29T20:30:28Z

‎Adjust Angles

2013-05-29T18:30:53Z

‎Adjust Rotation

2013-05-29T18:27:11Z

‎Adjust Rotation

2013-05-29T18:23:00Z

‎Start Over

2013-05-29T14:59:57Z

2013-05-29T14:52:27Z

2013-05-28T21:01:37Z

‎Dimension Types

@@ Line 27: / Line 27: @@
-'''2.)''' By '''clicking on the blue ring''' or by '''clicking and dragging the blue ring''' and the end of the straight length and '''keying in''' the length value.
+'''2.)''' By '''clicking on the blue ring'''/'''clicking and dragging the blue ring''' at the end of the straight length then '''keying in''' the length value.
@@ Line 45: / Line 45: @@
-'''2.)''' By '''clicking on the pink ring''' or by '''clicking and dragging the pink ring''' and '''keying in''' the angle value.
+'''2.)''' By '''clicking on the pink ring'''/'''clicking and dragging the pink ring''' then '''keying in''' the angle value.
@@ Line 62: / Line 62: @@
 [[File:ldadjustrot1.png|350px]]
-'''2.)''' By '''clicking on the green ring''' or by '''clicking and dragging the green ring''' and '''keying in''' the rotation value.
+'''2.)''' By '''clicking on the green ring'''/'''clicking and dragging the green ring''' then '''keying in''' the rotation value.
 '''3.)''' By '''entering a value''' into the rotation field in the left panel. ''Note: Leaving a rotation field blank will have the same effect as a zero.''

← Older revision		Revision as of 16:26, 19 June 2013
Line 97:		Line 97:

	'''2.)''' '''Click on the pink ring''' and '''key in "180"''' on the keyboard.		'''2.)''' '''Click on the pink ring''' and '''key in "180"''' on the keyboard.
		+
		+
		+	'''3.)''' If the part is being designed in '''length of straight mode''' [[File:strlen.png]], '''click the pink ring''' and '''drag the bend''' to 180°.

@@ Line 51: / Line 51: @@
 [[File:ldadjustangle2.png]]
 =='''Adjust Rotation'''==
@@ Line 64: / Line 67: @@
 [[File:ldadjustrot2.png]]
 =='''Dimension Types'''==
@@ Line 77: / Line 83: @@
 '''''Take caution''''' when using this function. Once a part has been started over, its information cannot be retrieved again.
 =='''180° Bends'''==

@@ Line 45: / Line 45: @@
-'''2.)''' By '''clicking on dragging the pink ring''' or by '''clicking and dragging the pink ring''' and '''keying in''' the angle value.
+'''2.)''' By '''clicking on the pink ring''' or by '''clicking and dragging the pink ring''' and '''keying in''' the angle value.
@@ Line 51: / Line 51: @@
 [[File:ldadjustangle2.png]]
 =='''Adjust Rotation'''==

@@ Line 64: / Line 64: @@
 '''2.)''' By '''clicking on the green ring''' or by '''clicking and dragging the green ring''' and '''keying in''' the rotation value.
-'''3.)''' By '''entering a value''' into the rotation field in the left panel. ''Note: Leaving a rotation field blank will be treated the same as a zero.''
+'''3.)''' By '''entering a value''' into the rotation field in the left panel. ''Note: Leaving a rotation field blank will have the same effect as a zero.''
 [[File:ldadjustrot2.png]]

@@ Line 80: / Line 80: @@
 =='''Start Over'''==
-'''To completely start over''' and delete all bend information, click the start over button. [[File:startover.png]] '''''Take caution''''' when using this function. Once a part has been started over, its information cannot be retrieved again.
+'''To completely start over''' and delete all bend information, click the start over button. [[File:startover.png]]
 =='''180° Bends'''==

@@ Line 15: / Line 15: @@
 [[File:lddeletebend.png|600px]]
 =='''Adjust Lengths'''==
@@ Line 24: / Line 27: @@
-'''2.)''' By '''clicking on the blue ring''' and the end of the straight length and '''keying in''' the length value.
+'''2.)''' By '''clicking on and/or dragging the blue ring''' and the end of the straight length and '''keying in''' the length value.
@@ Line 42: / Line 45: @@
-'''2.)''' By '''clicking on the pink ring''' and '''keying in''' the angle value.
+'''2.)''' By '''clicking on and/or dragging the pink ring''' and '''keying in''' the angle value.
@@ Line 48: / Line 51: @@
 [[File:ldadjustangle2.png]]
 =='''Adjust Rotation'''==
@@ Line 56: / Line 62: @@
 [[File:ldadjustrot1.png|350px]]
-'''2.)''' By '''clicking on the green ring''' and '''keying in''' the rotation value.
+'''2.)''' By '''clicking on and/or dragging the green ring''' and '''keying in''' the rotation value.
 '''3.)''' By '''entering a value''' into the rotation field in the left panel.
@@ Line 69: / Line 75: @@
 [[File:distApex.png|250px]] [[File:Straightlength.png|250px]]
 =='''Start Over'''==
 '''To completely start over''' and delete all bend information, click the start over button. [[File:startover.png]] '''''Take caution''''' when using this function. Once a part has been started over, its information cannot be retrieved again.
 =='''180° Bends'''==