Simulation Tutorial - Revision history

Fabcam1 at 15:48, 28 August 2013

2013-08-28T15:48:29Z

2013-07-15T15:52:18Z

2013-07-15T15:37:17Z

2013-07-15T15:35:05Z

2013-07-15T15:16:56Z

2013-07-15T15:11:29Z

2013-07-15T15:10:36Z

2013-07-15T14:58:39Z

2013-07-15T14:52:51Z

2013-07-15T14:51:29Z

← Older revision		Revision as of 15:48, 28 August 2013
Line 27:		Line 27:

	==='''Note'''===		==='''Note'''===
−	Before starting the tutorial, a part must be ~~created~~. This tutorial will be using the part that was created in the '''[[Linear 2D Designer Tutorial]]~~'''. '''Please complete the Linear 2D Designer tutorial before proceeding~~'''.	+	Before starting the tutorial, a part must be completed. This tutorial will be using the part that was created in the '''[[Linear 2D Designer Tutorial]]'''.

@@ Line 77: / Line 77: @@
 ==='''Step 5'''===
 '''Click the play button''' to watch the bending simulation with the normal bend order. Once the part is fully bent, the animation will reset back to the beginning and continuously loop through the simulation. '''Click the restart button once the part is complete''' to stop the animation and set it back to the beginning.
 [[File:simtut08.png|500px]] [[File:simtut09.png|500px]]

@@ Line 156: / Line 156: @@
 ==='''Step 11'''===
-'''Click the green check button''' to save the bend order and close the simulation window.
+'''Click the green check button''' to close the simulation window and save all bend order adjustments.
 [[File:simtut20.png|600px]]

@@ Line 153: / Line 153: @@
-The '''save and print buttons''' can be used to print an image or save a .bmp, .png, or .jpeg of the current position of the bending simulation shown in the frame above.
+==='''Step 12'''===
-[[File:simtut19.png|450px]]
+Notice how the '''bend order changes will be reflected in the results table''' at the top of the designer window.
 See the '''[[Simulation]]''' page for further information on each function in the Simulation plug-in.

← Older revision		Revision as of 15:16, 15 July 2013
Line 77:		Line 77:

	==='''Step 5'''===		==='''Step 5'''===
−	'''Click the play button''' to watch the bending simulation with the normal bend order. ~~The simulation will restart again once~~ the part is fully bent. '''Click the restart button ~~after~~ the ~~simulation~~ is complete''' to stop the animation and set it back to the beginning.	+	'''Click the play button''' to watch the bending simulation with the normal bend order. Once the part is fully bent, the animation will reset back to the beginning and continuously loop through the simulation. '''Click the restart button once the part is complete''' to stop the animation and set it back to the beginning.

← Older revision		Revision as of 15:10, 15 July 2013
Line 150:		Line 150:

	[[File:simtut15.png\|600px]]		[[File:simtut15.png\|600px]]
		+


Line 159:		Line 160:


−	See the [[Simulation]] page for further information on each function in the Simulation plug-in.	+	The '''save and print buttons''' can be used to print an image or save a .bmp, .png, or .jpeg of the current position of the bending simulation shown in the frame above.
		+
		+	[[File:simtut19.png\|450px]]
		+
		+
		+	See the '''[[Simulation]]''' page for further information on each function in the Simulation plug-in.

@@ Line 138: / Line 138: @@
 ==='''Step 9'''===
-Before the bending simulation is viewed, the speed of the animation will be adjusted. In the bottom left corner, there will be three different speed options: slow, normal, and fast. '''Click the fast button''' as shown below.
+Before the bending simulation is viewed, the speed of the animation will be adjusted. In the bottom left corner, there will be three different speed options: slow, normal, and fast. '''Click the fast button''' as shown below. This will cause the animation of the bending part to bend the part a bit quicker.
 [[File:simtut16.png|600px]]
@@ Line 150: / Line 150: @@
 [[File:simtut15.png|600px]]

@@ Line 68: / Line 68: @@
 ==='''Step 4'''===
-Next, make sure the '''bending order is set to the normal setting''' (bends go from 1 to 5, all are bend From Start ). If the order is not normal, '''click the normal bend order button'''.
+Next, make sure the '''bending order is set to the normal setting''' (bends go from 1 to 5, all are bent From Start ). If the order is not normal, '''click the normal bend order button'''.
 [[File:simtut10.png]]

@@ Line 53: / Line 53: @@
 ==='''Step 3'''===
-Next, the bending type will be changed. '''Click the bend type button''' near the bottom right corner.
+First, the bending type will be changed. '''Click the bend type button''' near the bottom right corner.
 [[File:simtut17.png|600px]]
@@ Line 68: / Line 68: @@
 ==='''Step 4'''===
-First, make sure the '''bending order is set to the normal setting''' (bends go from 1 to 5, all are bend From Start ). If the order is not normal, '''click the normal bend order button'''.
+Next, make sure the '''bending order is set to the normal setting''' (bends go from 1 to 5, all are bend From Start ). If the order is not normal, '''click the normal bend order button'''.
 [[File:simtut10.png]]