Spring-back Charts Tutorial - Revision history

Fabcam1 at 15:49, 28 August 2013

2013-08-28T15:49:53Z

2013-07-17T14:32:04Z

2013-07-17T14:24:12Z

2013-07-16T19:17:30Z

2013-07-16T17:03:13Z

2013-07-16T16:59:29Z

2013-07-16T16:47:53Z

2013-07-16T16:39:06Z

2013-07-16T16:29:33Z

2013-07-16T16:28:45Z

← Older revision		Revision as of 15:49, 28 August 2013
Line 20:		Line 20:

	==='''Note'''===		==='''Note'''===
−	Before starting the tutorial, a part and a die must be created. This tutorial will be using the part that was created in the '''[[Linear 2D Designer Tutorial]]''' and the die that was created in the '''[[Die Library Tutorial]]'''. ~~'''Please complete both the Linear 2D Designer and Die Library tutorials before proceeding.'''~~	+	Before starting the tutorial, a part and a die must be created. This tutorial will be using the part that was created in the '''[[Linear 2D Designer Tutorial]]''' and the die that was created in the '''[[Die Library Tutorial]]'''.

← Older revision		Revision as of 14:32, 17 July 2013
Line 20:		Line 20:

	==='''Note'''===		==='''Note'''===
−	Before starting the tutorial, a part and a die must be created. This tutorial will be using the part that was created in the '''[[Linear 2D Designer Tutorial]]''' and the die that was created in the '''[[Die Library Tutorial]]'''. '''Please complete both the Linear 2D Designer and ~~die library~~ tutorials before proceeding.'''	+	Before starting the tutorial, a part and a die must be created. This tutorial will be using the part that was created in the '''[[Linear 2D Designer Tutorial]]''' and the die that was created in the '''[[Die Library Tutorial]]'''. '''Please complete both the Linear 2D Designer and Die Library tutorials before proceeding.'''

← Older revision		Revision as of 14:24, 17 July 2013
Line 4:		Line 4:


−	The spring-back charts plug-in is used to record the attempted and achieved bend angles for each individual die. Once ~~at least 2~~ entries are added, a full chart of spring-back and achieved angles ranging from 1° to 180° will be generated.	+	The spring-back charts plug-in is used to record the attempted and achieved bend angles for each individual die. Once entries are added, a full chart of spring-back and achieved angles ranging from 1° to 180° will be generated.

← Older revision		Revision as of 19:17, 16 July 2013
Line 129:		Line 129:

	==='''Step 8'''===		==='''Step 8'''===
−	Now, say the part was created, but '''each 45° bend was slightly off'''. When bending these bends to 49.2°, they resulted in 46° after spring back instead of the intended 45°.	+	Now, say the part was created using these spring angles, but '''each 45° bend was slightly off'''. When bending these bends to 49.2°, they resulted in 46° after spring back instead of the intended 45°.

@@ Line 129: / Line 129: @@
 ==='''Step 8'''===
-Now, say the part was created, but '''each 45° bend was slightly off'''. When bending these bends to 49.2°, they resulted in 46° after spring back.
+Now, say the part was created, but '''each 45° bend was slightly off'''. When bending these bends to 49.2°, they resulted in 46° after spring back instead of the intended 45°.
-To fix this issue, another spring-back entry will be added to the chart. '''Open the spring-back charts plug-in again.'''
+To address this issue, another spring-back entry will be added to the chart. '''Open the spring-back charts plug-in again.'''
 [[File:spring03.png]]

← Older revision		Revision as of 16:59, 16 July 2013
Line 185:		Line 185:

	==='''Step 12'''===		==='''Step 12'''===
		+	Go back up to the top of the window and '''see the results chart'''. Each 45° bend will have a new spring angle that should be more accurate.
		+
		+	[[File:spring19.png]]
		+
		+
		+
		+
		+	==='''Step 13'''===
		+	'''The tutorial is complete!'''
		+
		+	See the '''[[Spring-back Charts]]''' plug-in page for more information on each function.

@@ Line 148: / Line 148: @@
 '''Click the add button'''. This will open the message box where the new spring back entry will be supplied.
@@ Line 163: / Line 166: @@
 '''The new entry will be added to the chart''' as shown below. Notice how the '''spring angle for 45° bends is adjusted in the full chart''' to the left.
-[[File:spring17.png]]
+[[File:spring17.png|600px]]
-==='''Step 10'''===

← Older revision		Revision as of 16:39, 16 July 2013
Line 163:		Line 163:


−	Notice how the spring angle for 45° bends is adjusted in the full chart to the left.	+	'''The new entry will be added to the chart''' as shown below. Notice how the '''spring angle for 45° bends is adjusted in the full chart''' to the left.
		+
		+	[[File:spring17.png]]
		+
		+

@@ Line 103: / Line 103: @@
 [[File:spring16.png|600px]]
@@ Line 161: / Line 165: @@
 Notice how the spring angle for 45° bends is adjusted in the full chart to the left.
 ==='''Step 10'''===

@@ Line 96: / Line 96: @@
 [[File:spring10.png|600px]]
@@ Line 145: / Line 152: @@
-'''Enter 46 into the achieved angle field and enter 49.2 into the spring/overbend angle field.'''
+'''Enter 46 into the achieved angle field and enter 49.2 into the spring/overbend angle field.''' After the angle values are entered, '''click the green check button'''.
 [[File:spring15.png]]