Template Designer Quick Start - Revision history

Fabcam1 at 17:15, 30 May 2013

2013-05-30T17:15:45Z

2013-05-30T17:04:00Z

2013-05-30T17:02:30Z

2013-05-30T17:01:14Z

2013-05-30T17:00:11Z

2013-05-30T16:59:21Z

2013-05-30T16:39:33Z

2013-05-30T15:56:56Z

2013-05-29T18:37:13Z

Created page with "=='''Adjust Lengths'''== =='''Adjust Angles'''== =='''Adjust Rotation'''== =='''Dimension Types'''=="

New page

=='''Adjust Lengths'''==

=='''Adjust Angles'''==

=='''Adjust Rotation'''==

=='''Dimension Types'''==

← Older revision		Revision as of 17:15, 30 May 2013
Line 48:		Line 48:


−	'''To choose a dimension type during the design process''', click one of the dimension options below the designer entry fields on the left panel.	+	'''To choose a dimension type during the design process''', click one of the dimension options below the designer entry fields on the left panel. ''Note: If the template only has one dimension option, these will not be shown.''

	[[File:tempdim2.png\|600px]]		[[File:tempdim2.png\|600px]]
		+
		+
		+
		+
		+	=='''180° Bends'''==
		+	In the template designer, 180° bends are included in certain templates. To create a part with a 180° bends in the template designer, one of these templates with a predefined 180° bend must be used.
		+
		+	[[File:temp180.png\|600px]]

@@ Line 8: / Line 8: @@
 =='''Adjust Angles'''==
-'''Only certain template parts allow for an angle adjustment'''. If an angle adjustment is available, the angle field will have a "Bend Angle" label next to it. '''To change the angle''', enter a new value into the angle field.
+'''Only certain template parts allow for an angle adjustment'''. If an angle adjustment is available, the angle field will have a "Bend Angle" label next to it.
 [[File:tempangles.png|600px]]

@@ Line 8: / Line 8: @@
 =='''Adjust Angles'''==
-Certain template parts allow for an angle adjustment. If an angle adjustment is available, the angle field will have a "Bend Angle" label next to it. '''To change the angle''', enter a new value into the angle field.
+'''Only certain template parts allow for an angle adjustment'''. If an angle adjustment is available, the angle field will have a "Bend Angle" label next to it. '''To change the angle''', enter a new value into the angle field.
 [[File:tempangles.png|600px]]

@@ Line 28: / Line 28: @@
 Each template will have between one and three different dimension type options: Inside, Center, or Outside. These can be chosen at the initial template selection or during the design process.
-* [[File:center.png]] or [[File:center2.png]] '''Center Dimensions:''': The dimensions will be measured from the center line of the tube.
+'''To choose a dimension type during the design process''', click one of the dimension options below the designer entry fields on the left panel.
-* [[File:inside.png]] or [[File:inside2.png]] '''Inside Dimensions''': The dimensions will be measured from the outside edges of the tube.
+[[File:tempdim2.png|600px]]

@@ Line 1: / Line 1: @@
 =='''Adjust Lengths'''==
-To adjust the lengths of a template part, enter values into the designer entry fields that mark the straight lengths of the part.
+'''To adjust the lengths''' of a template part, enter values into the designer entry fields that mark the straight lengths of the part.
 [[File:templengths.png|600px]]
@@ Line 18: / Line 18: @@
 The ability to add rotations to a template part is '''only available if the template rotation plug-in is included''' in the current version of the software.
-To add rotations to bends, enter new values into the rotation fields below the arrow icon in the left panel.
+'''To add rotations to bends''', enter new values into the rotation fields below the arrow icon in the left panel.
 [[File:temprotate.png|600px]]

← Older revision		Revision as of 16:59, 30 May 2013
Line 16:		Line 16:

	=='''Adjust Rotation'''==		=='''Adjust Rotation'''==
		+	The ability to add rotations to a template part is '''only available if the template rotation plug-in is included''' in the current version of the software.

		+	To add rotations to bends, enter new values into the rotation fields below the arrow icon in the left panel.
		+
		+	[[File:temprotate.png\|600px]]

@@ Line 3: / Line 3: @@
 [[File:templengths.png|600px]]
 =='''Adjust Angles'''==
@@ Line 13: / Line 16: @@
 =='''Adjust Rotation'''==
 =='''Dimension Types'''==