Grapple Designer

Description

The Grapple Designer allows parts to be designed in full 3D. Parts are created by clicking and dragging the grapple tool around to define the angles, rotations, and lengths of the part.

How To

Start Up

To access this designer, click the grapple button on the start up page. This will open up a new, blank part design.

Part Design

Once a new linear dynamic part design window has been opened, a new part can be created.

First, a die and material should be chosen. This can be done by clicking on the drop down menus next to the die and material icons in the top left corner of the screen.

If any cut-off is necessary, enter the amount needed into the start and end cut-off fields. The first/top field represents the cut-off at the start of the part and the second/bottom field represents the cut-off at the end of the part.

Now a part can be designed by clicking and dragging the grapple handles in the direction of the part. When a new part is opened, the grapple tool will start out in the center of the 3D axis, as shown to the right.

The grapple tool has six different handles. Each will pull the current length of the part in a certain direction.

To start designing the part, click and drag one of the handles in the desired direction. This can also be done by clicking the handle and directly keying in the distance value wanted or by entering values into the fields on the left.

As the part is being drawn, the lengths, angles, and rotations will be automatically generated in the fields on the left of the screen. See image below.

Once more than one angle is applied to a bend (Example: Pulled the light blue handle and then pulled the red handle), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel. The small axis icon will show which axes the angle is along. These can be also edited by entering values directly into the given fields.

If more than two angles are added to the bend, two more angle values will be generated. These will also have axis icons that will show which axes the angles are along. These can also be edited by directly entering values into the fields.

Individual bends' angles can be locked by clicking on and toggling the lock icon on or off. When a bend is locked, the angles of the bend will be locked in place if any attempts to change them are made. While locked, dragging the grapple tool around will only adjust the length of the straight after the bend.

Note: Be very careful when adjusting locked bends! Depending on the combination of angles on the bend, adjusting a locked bend can sometimes force the straight length to extend far past the intended length.

To add a bend, either double click the grapple tool or click the add bend button . Once a new bend has been added, the main axis will move to the new bend. See image to the right.

To remove the last bend, click the delete bend button .

To select and edit bends, first select the bend that will be edited. This is done by clicking directly on the bend in the part display. When hovering the mouse over a bend, it will show a grey grapple shape around the bend, as shown to the right. Click on it to select. Bends can also be selected by clicking on the bend in the bend list, as shown below.

Controls and Options

To adjust the scale at which the part is being viewed in the part display, click either the large, medium, or small scale buttons . See images below for an explanation of each scale.

Notes can be attached to the part design project using the note button .

To add another bend to the part, click the add bend button .

The auto-zoom option can be turned on or off using the auto-zoom button . When activated, auto-zoom will zoom in or out to accommodate the size of the part. For example, if a length is originally 200 and is changed to 2000, it may extend past the part display's extend. Auto-zoom will zoom out to make sure the whole part is visible.

To completely start over and delete the whole part design, click the start over button .

To delete the last bend that was added to the part, click the delete bend button .

To lock or unlock bends, click on/toggle the lock button (locked)/ (unlocked). When the bends are locked, the bend and each consecutive bend will be moved whenever a bend's location is adjusted. When the bends are unlocked, when the bend is adjusted it will be the only part that will move. The rest of the bends will remain stationary. See image below for an example of this.